Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Thermo Products OC2-56

downloaded: 10File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

PLATE PART NO. TOP-25752 BTM-35733 35750 35750 35750 35750 MTG. PLATE GASKET PART NO. 330090 330088 330088 330088 330088 **NOZZLE SIZE .50-60A .60-60A* .75-60A* .90-60A* 1.10-60A* NOZZLE PART NO. 380393 380394 380395 380396 380397 OIL PUMP PRESSURE 170 PSI 145 PSI 145PSI 145 PSI 150PSI BURNER F3 F3 F5 F5 F5 BURNER PART NO. 380215 380215 380216 380216 380216 * A refers to hollow pattern nozzle ** NOTE: The reason the Riello burner nozzle sizes are smaller than the standard Thermo Pride burner noz

Thermo Products Built Tough for Lifetime Comfort OMC-70

downloaded: 7File size: 492 kb    Manafacture: Thermo Products  
Category: Electric Heaters

Since 1955, Thermo Pride has backed our heat exchangers with the industry’s only transferable Limited Lifetime Warranty. We also offer a full five-year parts warranty at no additional cost. Together, these make up Thermo Pride’s unique “Peace of Mind” warranty…our assurance to you that, when you buy Thermo Pride, you buy the best. Comfort Comfort is the purpose behind any heating system. “Temperature rise” makes the difference between feeling warm, comfortable air from the registers in your home

Thermo Products OH5-85

downloaded: 6File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

. WARNING: NEVER burn garbage or refuse in your furnace. Never try to ignite oil by tossing burning papers or other material into your furnace. . WARNING: Thermo Pride oil furnaces are designed to burn No. 1 or No. 2 distilate fuel oil. NEVER USE GASOLINE OR A MIXTURE OF OIL AND GASOLINE. . CAUTION: DO NOT ATTEMPT TO START THE BURNER WHEN: 1. Excess oil has accumulated, 2. The furnace is full of vapors 3. The combustion chamber is very hot. IF ONE OR MORE OF THESE CONDITIONS EXIST, CONTACT A QUA

Thermo Products MHA1-100

downloaded: 5File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

NOTICE: If the furnace is installed in a home or structure being remodeled, dust levels may be much higher than normal The filter must be inspected daily and cleaned as needed until dusty conditions have been eliminated. Any replacement motors not obtained through Thermo Products should be lubricated according to the motor name plate. : This furnace is not to be used for temporary heating of buildings or structures under construction. UPFLOW FURNACE (CHX1/CHB1/MHA1) The filter rack or drop chute

Thermo Products MDA1-125

downloaded: 5File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

SAFETY INFORMATION 1 II. GENERAL INSTRUCTIONS 5 III. FURNACE OPERATION 10 A. WARNINGS BEFORE OPERATING 10 B. OPERATING INSTRUCTIONS 10 C. SHUTDOWN PROCEDURE 11 IV. HOMEOWNER/USER MAINTENANCE INSTRUCTIONS 11 (ROUTINE MAINTENANCE) A. ANNUAL INSPECTION 11 B. FILTER MAINTENANCE PROCEDURE 12 C. VISUAL INSPECTION PROCEDURE 14 All installations and services must be performed by qualified service personnel. I. SAFETY INFORMATION This and the following page contain reproductions of the various warning an

Thermo Products CDB1-75

downloaded: 4File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

7 Figure 3 All installations and services must be performed by qualified service personnel. 8 3. : To avoid injury from moving parts, shut off the power to the furnace before removing blower compartment door. 4. : Keep furnace free and clear of combustible materials, gasoline, and other flammable liquids and vapors. 5. The furnace needs air for combustion and ventilation for safe and proper operation. IMPORTANT: Do not block or obstruct air openings on the furnace, air openings communicating wit

Thermo Products CDX1-100N

downloaded: 3File size: 2 mb    Manafacture: Thermo Products  
Category: Electric Heaters

WHAT TO DO IF YOU SMELL GAS: • DO NOT TRY TO LIGHT ANY APPLIANCE. • DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE IN YOUR BUILDING. • LEAVE THE BUILDING IMMEDIATELY. • IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS. • IF YOU CANNOT REACH YOUR GAS SUPPLIER; CALL THE FIRE DEPARTMENT. INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER. (REFERRED TO IN THESE INSTRUCTIONS AS A QUALIFIED

Thermo Products CHX1-125N

downloaded: 2File size: 2 mb    Manafacture: Thermo Products  
Category: Electric Heaters

If any of the original factory supplied furnace wiring is replaced or a separate device other than the thermostat is wired internal to the unit 105°C thermoplastic or equivalent wire must be used. 28 All installations and services must be performed by qualified service personnel. IV. STARTING THE UNIT A. SEQUENCE OF OPERATIONS AT ANY TIME THE GAS VALVE IS NOT ENERGIZED CONTINUOUS SAFE OPERATION CHECK IF FLAME SIMULATION CONDITION PRESENT OR ROLL-OUT SWITCH OPENS, SYSTEM ENERGIZES INDUCER FAN FOR

Thermo Products OH3-72

downloaded: 2File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, OR SERVICE AGENCY. PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE PERFORMING ANY SERVICE OR MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WI

Thermo Products MHA1-125

downloaded: 2File size: 1 mb    Manafacture: Thermo Products  
Category: Electric Heaters

Clean filters by vacuuming, tap water rinsing, hosing or dipping in an ordinary detergent solution. After cleaning, replace completely dry filter, mesh side down on the filter rack on the top of the furnace. Replace front door. Turn on power to furnace. 12 All installations and services must be performed by qualified service personnel. Figure 4. FILTER REPLACEMENT See Table 1 for minimum heating filter areas required for the different types of filters available should the filter used require rep





Category