1. Place the choke lever in Position 2. NOTE: The blue choke lever must be in Position 2 to remove the air filter/ muffler cover. 2. Remove the four (4) screws securing the air filter/muffler cover (Fig. 17). Use a T-20 Torx bit screwdriver. 3. Pull the cover from the engine. Do not force. Blue Choke Lever Screws Screws Position 2 Fig. 17 Cleaning the Air Filter Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain your air filter p
.147495 Bump Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180814 Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .753-1229 Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . .682075 For specific replacement parts, refer to the parts list located on the inside back cover of this manual. 25 SECTION 8: TROUBLESHOOTING GUIDE Trouble Possible Cause(s) Corrective Action ENGINE WILL • On/Off control in the STOP position • Turn On/Off control to ON NOT STA
430355 10.19.09 SR Printed in the U.S.A. 20 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302) AUGER HOUSING / IMPELLER ASSEMBLY 11 10 11 11 11 1 2 3 4 5 6 7 9 9 9 8 12 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 25 26 27 28 29 30 31 31 32 33 34 35
This modern outdoor power tool has been fully assembled and designed to provide you with many hours of useful service. You will find it to be a great labor-saving device. This operator's manual provides you with easy-to-understand operating instructions. Read the entire manual and follow all of the instructions to keep your new outdoor power tool in top operating condition. The other manual that came with your power tool, the parts manual, contains all of the information that you need to order
Be sure the guard mounting bracket slides into the slot on the edge of the cutting shield. Rotate the shield into place, counterclockwise. The holes in the guard mounting bracket and cutting attachment shield will line up (Fig. 3). 2. From inside the cutting attachment shield, push the square bolt through the hole until the threaded end protrudes through the guard mounting bracket (Fig. 4). Guard Mounting Bracket Shaft Housing Square Bolt Cutting Attachment Shield 3. Put the washer on the bolt,
Dispose of the oil according to Federal, State and local regulations. 5. Refill the crankcase with 3.04 fluid ounce (90 ml) of SAE 30 SF, SG, SH oil. NOTE: Use the bottle and spout saved from initial use to measure the correct amount of oil. Pour fresh fuel into the bottle and fill it to the top of the label. The top of the label on the bottle measures approximately 3.04 ounces (90 ml). Check the level with the dipstick. If the level is low, add a small amount of oil and recheck. Do not overfill
With chute rotator head and chute bracket aligned, spring. po si tion chute rotator head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. AUGER CONTROL ROD CONTROL ARM VINYL SLEEVE LOOP OPENING UP CHUTE ROTATOR HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATOR HEAD MOUNT ING BRACKET CHUTE BRACKET FIG. 7 ALIGN BEFORE TIGHTENING LOCKNUT FIG. 5 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factor
Snowthrower TRACTOR ASSEMBLY S/N 420280100101- 420280199999 85 0 J41 40 . . Ve TOUCH-UP PAINT SERVICE PARTS 200 Black Spray Paint 202 Loctite 242 201 Green Spray Paint 203 Tire Chains 7Г* Щ. 32 35 «к 29 Ч1 2 Model 42028 Ref.# Part# Description Qty. Ref.# Part# Description Qty. 1 1703539 Handle Grip............................................ 2 51 1756065021 Frame.................................................. . 1 2 1750796 Bumper..........................................