Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Dakota Digital UTV-1500

downloaded: 1File size: 289 kb    Manafacture: Dakota Digital  
Category: Boats Accessories

UTV-1500 Gauge for Polaris RZR MPHABTEMPOILkm/hEFVOLTSFUEL1234567SERVHRTachometer bar graphSpeed displayLight sensor locationMessage centerSpeed unit indicators4x4 on indicatorCheck engine indicatorGear position indicatorsFuel bar graph Operation menu Switch functions: Pressing the switch during normal gauge operation will move the message center through the below display functions. ... Odometer ... A Trip odometer A (hold switch to reset) ... B Trip odometer B (hold switch to reset) SERV ......

Dakota Digital PAC-3500

downloaded: 1File size: 67 kb    Manafacture: Dakota Digital  
Category: Doors and Windows

3Speeds are approximate and may vary slightly depending on application Wiring to a door lock motor. Dakota Digital RLY-2 relay pack shown. To PAC-3500Lock output. FUSED 12V POWERTo PAC-3500Unlock output. The wires between the switch and the motor will need to be cut, and the relay pack wired in between as shown. Fused 12V power. MOTORMOTORSWITCHPURPLEGREENBROWNWHITEBLUERELAYREDsmall wireGREENPACKBLUEsmall wireDUAL+12v on lock+12v on lock Indicator LEDs The green LED will turn on when the auto-lo

Dakota Digital ODY-16-1

downloaded: 0File size: 69 kb    Manafacture: Dakota Digital  
Category: Time Clocks

incorporates the reliability and quality of our standard gauges, along with several unique features and easy mounting. These features include: • Quartz accuracy. • Night dimming feature. • Very low standby power to prevent battery drain. • High Visibility VFD display for sunlight readability. The Odyssey series clock displays the current time in 12 hour format. The high brightness display matches our other Odyssey and STR series gauges and has the same night brightness dimming capability. Operat

Dakota Digital MULTI GAUGE UTV-1200

downloaded: 3File size: 130 kb    Manafacture: Dakota Digital  
Category: Time Clocks

UTV-1200 Multi Gauge for 2008 Yamaha Rhino Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience. 00000.0 Odometer 12:00A Clock (hold left switch to set) Setting clock: Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode H 0.0 Hourmeter Right switch functions Pressing the right function switch during norma

Dakota Digital MAN#650277

downloaded: 1File size: 267 kb    Manafacture: Dakota Digital  
Category: Boats Accessories

Remove the clusters from the vehicle. The procedure for the speedometer and tachometer clusters are the same, but only one side is shown in the photos. 2. Remove the three screws holding the bezel on to the gauge can. Two are indicated by the upper arrows in the photo at right; one is on the bottom side of the can and cannot be seen here. After the bezel is set aside, remove the two screws near the center of the can to remove the original gauge. On the speedometer can (shown) you will also need

Dakota Digital MAN #650134

downloaded: 0File size: 156 kb    Manafacture: Dakota Digital  
Category: Time Clocks

These features include: · Quartz accuracy · Night dimming feature · Very low standby power to prevent battery drain · High visibility VFD display for sunlight readability · Displays current time in 12 hour format Wiring: Clock BLACK Connect to a good ground point in the vehicle RED Connect to switched 12 volt power point (An accessory terminal will work for this) ORANGE Connect to a constant 12 volt power point (This will keep the correct time) BLUE Connect to the taillight circuit +12V when lig

Dakota Digital LED Tail Lights LAT-NR421

downloaded: 1File size: 215 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside of the housing.The flat side of the mounting disk should betoward the outsideand thes

Dakota Digital LED Tail Lights LAT-NR401

downloaded: 0File size: 142 kb    Manafacture: Dakota Digital  
Category: Other Home Accessories

2. Remove the tail light housing from the car. 3. Remove any body trim from the housing so the screws holding the lens on are exposed. 4. Remove the tail light lens. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoi

Dakota Digital LED Tail Lights LAT-NR370

downloaded: 0File size: 222 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

B Kit Includes: m, m Installation: 1. Remove the screws and the tail light lens. 2. Remove the tail light bulb. 3. Now is a good time to clean or replace the lens and housing if necessary. 4. The new LED assembly will mount into the original light bulb socket. Push it into the socket and turn it clockwise to lock it in. 5. Repeat for the other tail light. 6. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash, you will need to upgrade your flasher. If

Dakota Digital LED Tail Lights LAT-NR362

downloaded: 0File size: 145 kb    Manafacture: Dakota Digital  
Category: Other Home Accessories

Now is a good time to clean and inspect the lenses also. If the lenses are in bad shape, a replacement set is recommended. MAN#650205 11. Push the bulb base plug and wire from the LED assembly through the light bulb hole in the back of the tail light housing. 12. While working the wire harness through the light bulb opening, place the LED assembly into the housing. The mounting plate is marked with up arrows that should point to the top of the tail light housing when the LED assembly is insta





Category