Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Delta Wood Lathe

downloaded: 0File size: 19 kb    Manafacture: Delta  
Category: Lathe

Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment should comply with ANSI S3.19 standards, and dust mask protection should comply with MSHA/NIOSH certified respirator standards. 7. DO NOT WEAR TIE, GLOVES, or loose clothing. REMOVE WATCH, RINGS, and other jewelry. ROLL UP SLEEVES. 8. USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly. 9. ROUGH CUT THE WORKPIECE as close as possible to the finished shape befor

Delta WILLIAMSBURG 2804

downloaded: 0File size: 463 kb    Manafacture: Delta  
Category: Plumbing Product

Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 2 REAR OF SINK 4 5 6 3 1 SINK DRAIN HOLE FLAT SIDE OF GASKET MUST FACE DOWN 1 2 Fig. A. 2 1 FLAT SIDE OF GRAY LOCKNUT MUST FACE UP INSTALL GRAY LOCKNUT 5 Install GRAY LOCKNUT (1) onto DRAIN BODY (2) fro

Delta Widespread Lavatory Faucet 31730001

downloaded: 0File size: 1 mb    Manafacture: Delta  
Category: Plumbing Product

Place it in the sink outlet. From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly. Tighten the retainer nut. Place the plunger assembly in the drain. Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster. Install and ha

Delta Widespread Lavatory Faucet 31263XX1

downloaded: 0File size: 1 mb    Manafacture: Delta  
Category: Plumbing Product

Install the spout. Rotate the spout escutcheon if necessary, so that the hole for the pull rod is at the rear. Tighten the mounting nut. Tighten the tensioning screws. Screw the connecting hoses into the spout tee. Slide the 3/8" compression nuts and ferrules over the ends of the hoses. Connect the hoses to the valve outlets. Use two wrenches so that the hoses do not twist or become loosened from the spout tee. Install the supply lines (not included). Install the drain. Turn on the water and che

Delta Water Pump Series CP43D2001

downloaded: 1File size: 402 kb    Manafacture: Delta  
Category: Plumbing Product

Model CP43D2001 is cost down solution. * All readings are typical values. * Specifications are subject to change without notice. 23 http://www.deltaww.c<

Delta Water Pump Series CP43A2003

downloaded: 0File size: 402 kb    Manafacture: Delta  
Category: Plumbing Product

for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values. * Specifications are subject

Delta VFB25AX

downloaded: 0File size: 1 mb    Manafacture: Delta  
Category: Fans

2Step Insert the mounting springs into the slots and mount the grille to the body. 5Step Insert the duct into the duct connector. 3Step 4405 Cushing Parkway | Fremont, CA 94538 tel 1.888.979.9889 | DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc.(“ Delta Electronics” ) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original

Delta VFB25AEH

downloaded: 1File size: 1 mb    Manafacture: Delta  
Category: Fans

5-3. Ensure the distance between ceiling and fan body for the thickness of grille. 5-4. Secure the suspension bracket to joists by using screw. 5-5. Secure the suspension bracket to fan body by using screw. 5-6. Follow step 6 to 9 of installation to complete the installation work. 6. Duct Connection Outside Gradient 1°~2°Inspection Hole Grill Body Tape Duct Inside Ceiling 6-1. Insert the duct into the duct connector and tape all ductworks connection to make them secure and air tight. 6-2. Instal

Delta VFB25ADH

downloaded: 0File size: 1 mb    Manafacture: Delta  
Category: Fans

6-2. Install the duct with a gradient 1°~2° to the outside. 7. Connect Wiring 7-1. Follow all local electrical and safety codes. 7 -2. N EVER place a switch where it can be reached from a tub or shower. 7-3. Connect wires as shown in wiring diagrams. 7-4. Using wire nuts, connect house power wires to ventilating fan wires. 7-5. 14 AWG (2.1 mm2) is the smallest conductor that shall be used for branch-circuit wiring. 8. Test Run and Grille Attachment 8-1. With the power on, check for abnormal vibr

Delta VFB25AD

downloaded: 8File size: 1 mb    Manafacture: Delta  
Category: Fans

Ventilation Fan Installation Guide The Breez Ventilation System is easy to install Two basic types of installation are shown: in new or existing construction. Body Wood Frame Installation Joist Mounting Installation Make sure that the dimensions of the opening are suitable for installation and follow the steps below. Joist Joist Wood Frame Step 1 Attach the duct connector to the wood frame with taping screw. Wood Frame Wood Frame Duct Connector Taping Screw Step 2 Insert the body into the wood f





Category