Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Dish Network VIP622

downloaded: 2File size: 2 mb    Manafacture: Dish Network  
Category: Satellite Receivers

InstructionsAdditional Information 1 Turn the device on. 2 Press and hold the mode button until all the other mode buttons light up, and then let go of the button. The mode button flashes. 3 For AUX mode only. Press 0 for a second TV, or 1 for a second VCR, or 2 for a tuner, or amplifier. Then press the STAR (*) button. 4 Press POWER. Use the device’s front panel buttons or its remote control. For example, hold TV for a TV until all of the other mode buttons light. When you let go, TV will flash

Dish Network VIP612

downloaded: 0File size: 1 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Changing the Remote Control Address Because UHF signals travel long distances and go through walls, a neighbor’s remote may control your receiver by mistake. To prevent this, you can change the remote address. 1 Press SYSTEM INFO on the receiver's front panel. The System Information screen displays on the TV and shows the Remote Address. Write down the Remote Address: 2 Press and hold SAT on your remote control for about three seconds, until all of the mode buttons light up, and then release SAT

Dish Network VIP222

downloaded: 0File size: 2 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Use the following instructions to make your remote control operate more efficiently with your receiver. Changing the Address for Remote Control 2 Because UHF signals travel long distances and go through walls, a neighbor’s remote may control your receiver by mistake. To keep this from happening, you can change the remote address. You can also use these instructions to change the address on Remote Control 1. 1 Press SYSTEM INFO on the receiver's front panel. The System Information screen displays

Dish Network VIP211

downloaded: 2File size: 12 mb    Manafacture: Dish Network  
Category: Satellite Receivers

• PCM Only - Select this option only if the stereo system or amplifier cannot decode Dolby Digital signals. • Dolby Digital/PCM - Select this option only if the stereo system or amplifier can decode both Dolby Digital and Linear PCM signals. The audio output is also dependent on what is present in the program you are watching. The table below shows what type of output you will hear: Signal Present in Program Optical Output Setting Dolby Digital PCM Both Dolby Digital Only Dolby Digital PCM Dolby

Dish Network ViP 922 SlingLoaded

downloaded: 0File size: 224 kb    Manafacture: Dish Network  
Category: Satellite Receivers

You may also order DISH Network pay-per-view Services by calling 1-877-DISH-PPV (3474-778) and using our automated system, or speaking with a live operator at one of our customer service centers; in either case, a fee will apply as detailed in Section 2(D). Pre-Pay Promotion customers may only order pay-perview Services by calling 1-877-DISH-PPV (3473-778). G.Accessing the Internet Through Your Receiver. Some of our receivers can be used to access websites and information on the Internet. Neithe

Dish Network VIP 722

downloaded: 0File size: 9 mb    Manafacture: Dish Network  
Category: Receivers & Amplifiers

Satellite Receiver The ViP622 DVR and ViP722 DVR are dual-tuner satellite receivers with digital video recorders. With either receiver you can view/record standard-definition (SD) and high-definition (HD) DISH Network programming on two TVs or view/record over-the-air digital/HD broadcasts on the nearby HDTV. • Nearby TV (TV1)—Connect to an HDTV to view SD and HD DISH Network programming and over-the-air digital/HD broadcasts. Programming from the receiver is delivered to the nearby TV using sho

Dish Network Two-TV DVR

downloaded: 0File size: 3 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Dish Network TV2

downloaded: 1File size: 3 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Unless changed, factory default for TV2 is channel 60. Refer to the "How to Watch TV on TV2" section in this guide for correct channel setup or use the RECOVER button. Your satellite receiver is in "Single Mode" and "Shared View" is disabled. To watch what TV1 is watching, simply enable the Shared View option. To watch a program on TV2 that is different than what is being viewed on TV1, press the MODE button on the front of the satellite receiver to put it in Dual Mode. See your User's Guide fo

Dish Network TV1

downloaded: 0File size: 3 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Refer to the "How to Watch TV on TV1" section in this guide for the correct input. Why doesn't my PIP button seem to work? You can only view Picture-In-Picture when in Single Mode. Press the MODE button on the front of your receiver so that the Single Mode light is on, then use the blue PICTURE-IN-PICTURE buttons as desired. What should I do if my remote control doesn't seem to operate my satellite receiver? • Try pressing the SAT Mode button. • Check to make sure you are using the correct rem

Dish Network SoloDVR ViP 612

downloaded: 0File size: 12 mb    Manafacture: Dish Network  
Category: Satellite Receivers

Table of Contents Table of Contents Important Safety Instructions .........................vii Introduction ........................................................1 WELCOME....................................................................2 HOW TO USE THIS GUIDE .............................................2 ABOUT YOUR DISH NETWORK ACCOUNT .....................4 WATCHING TV NOW.....................................................5 ADDITIONAL SERVICES ...........................................





Category