Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Dolmar TB5018CC, TB5020CC

downloaded: 1File size: 1 mb    Manafacture: Dolmar  
Category: Chainsaws

Lubrication of the sprocket tip is recommended after 10 hours of use or once a week, which ever occurs first. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gun (optional) is recommended for applying grease to the guide bar sprocket tip. The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip. Fig. 37 To lubricate the sprocket tip: 1. Move the STOP switch down. NOTE: It is not necessary to remove

Dolmar TB4516CC

downloaded: 0File size: 28 mb    Manafacture: Dolmar  
Category: Chainsaws

. . . . . . . . . .13 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Warranty Information . . . . . . . . . . . . . . . . . . . . . . .20 Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover Copy the model and parent part number here: Copy the serial number here: Make sure you carefully read and understand this manual before starting or operating this equipment. THIS PRODUCT IS COVERED

Dolmar TB3516NT

downloaded: 0File size: 265 kb    Manafacture: Dolmar  
Category: Chainsaws

C-6CG-9.5 C RING 1 60 MC-6PC05-14.7 PIN 26 MC-6014-210502 WASHER 1 61 MC-6PC4.4-35 PIN 1 27 MC-6228-210104 GEAR BEARING ASS'Y 1 62 MC-6SQAB-04-06 SCREW 28 MC-6077-211501 COVER 1 63 MC-6WFB-03-12 WASHER 1 29 MC-6057-210102 WASHER 1 64 MC-6SDABB03-15 SCREW 30 MC-6CC-10 C RING 1 65 MC-6158-211502 PLATE 1 32 MC-6SDABB03-18 SCREW 1 66 MC-6SLABB03-06 SCREW 33 MC-6228-210105 OIL PUMP ASS'Y 1 67 MC-6010-211301 WIRE 1 34 MC-6188-211501 PULL BAR 1 68 MC-6SDABB04-14 SCREW 3 35

Dolmar TB3516

downloaded: 0File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Ensure that the WARNING: power cord is disconnected before performing any maintenance on your saw. Sprocket Tip Lubrication The sprocket tip on CAUTION: your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. Lubrication of the sprocket tip is recommended after each saw use. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gu

Dolmar PS-7900

downloaded: 0File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Dolmar PS-7300 H

downloaded: 0File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Dolmar PS-7300

downloaded: 4File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Dolmar PS-6400 H

downloaded: 2File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Dolmar PS-6400

downloaded: 6File size: 2 mb    Manafacture: Dolmar  
Category: Chainsaws

Dolmar PS-5100 SH

downloaded: 0File size: 3 mb    Manafacture: Dolmar  
Category: Hair Clippers

(4) Reset the filter to the fuel tank, and securely tighten the fuel tank cap. (5) Then, continue to operate the engine until it stops. (6) Remove the spark plug, and drip several drops of engine oil through the spark plug hole. (7) Gently pull the starter handle so that engine oil will spread over the engine, and attach the spark plug. (8) During storage, in order for the machine to become uprighting, please keep. (9) Keep the drained fuel in a special container in a well-ventilated shade. 16 F





Category