Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Havis-Shields WGI-F7-H

downloaded: 0File size: 119 kb    Manafacture: Havis-Shields  
Category: Doors and Windows

. 2. Mount window guards: Note: window guards have holes around perimeter for permanent mounting. These holes are not used with hinge kit. They also come flat in shipping. The guard must be pre-bent (outward) so it fits tight against the door window frame. Do not use holes on side of window guard to mount with the hinge application! 1. Hold window guard with pre-assembled hinge and upper bracket onto window frame. 2. Make sure guard is centered on window. 3. Attach hinge to lower door panel

Havis-Shields WGI-F13

downloaded: 2File size: 109 kb    Manafacture: Havis-Shields  
Category: Doors and Windows

Hold window guard up to the window frame, and while pushing down against the door window frame, mark mounting hole locations. Remove guard and drill out mounting holes with 1/8” drill bit. Attach guards with #10 X 1/2” sheet metal screws. FORD EXPLORER WINDOW GUARD POSITIONS MODEL WGI-F13 POSITION #1 DRIVERS SIDE PASSENGER DOOR F13-1 POSITION #6 PASSENGER SIDE PASSENGER DOOR F13-6 Consolidator' • Kwik-Raze’ • Collins Dynamics' • Kwik-Kit" PrisonerTransports • K-9Transports 75 Jack

Havis-Shields WGI-F11

downloaded: 2File size: 109 kb    Manafacture: Havis-Shields  
Category: Doors and Windows

The bottom of each guard is numbered, signifying its’ location. 2. Open door and hold the window guard up to the window door frame. NOTE: The angle at the bottom of the guard framework faces towards the outside of the car. The guard framework fits evenly around the window frame. 3. Mark a few holes at the top of the door frame using the pre-drilled holes on the guard framework as a guide. Note: Do not mark holes for the sides or bottom yet. 4. Remove window guard and drill holes as marked wi

Havis-Shields WGI-D23-1 & 6

downloaded: 0File size: 247 kb    Manafacture: Havis-Shields  
Category: Doors and Windows

They will need to be installed first. 'üïïiïïKîï; ^ ‘ïï!ïîïrÂ4 и»4 * WGI-D23-INST-10-06 INSTALL WINDOW GUARDS • Loosely attach upper mounting bracket to window guard using H” x /” tamper proof screws and flat washers. (This step may already be done during shipping) • Position screen to vehicle as shown in photo #2. • Make sure you have the window guard centered on the door. • Mark, drill 1/8” holes, and attach lower mount using #10 x /” screws as shown in photo #3. Note: Be sure the u

Havis-Shields WGI-D22

downloaded: 1File size: 247 kb    Manafacture: Havis-Shields  
Category: Doors and Windows

Bend window guard so it contours the door as shown in photo #1. Determine the proper window guard for each window. If installing aluminum door panels refer to those instructions at this time. They will need to be installed first. 2. 3. WGI-D22-INST-10-06 INSTALL WINDOW GUARDS • Loosely attach upper mounting bracket to window guard using H” x /” tamper proof screws and flat washers. • Position screen to vehicle as shown in photo #2. • Make sure you have the window guard centered on the d

Havis-Shields Telescoping Computer Base C-TCB-7-IMP

downloaded: 2File size: 80 kb    Manafacture: Havis-Shields  
Category: Optical Devices

Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit /-20 x /” Hex head bolt & /” Flat washer Spacer Bracket w/ /-20 x /” Hex head bolt & /” Flat washer Telescoping pole assembly Pole support assembly C-TCB-7-IMP-INST-12-04 SUB ASSEMBLY: 1. Confirm receipt of all hardware and components. 2. Install Chevrolet Impala Specific C-Series-IMP Consolidator® into vehicle using hardware and instructions provided. 3. Deter

Havis-Shields Telescoping Computer Base C-TCB-21

downloaded: 1File size: 58 kb    Manafacture: Havis-Shields  
Category: Optical Devices

Mount C-TCB-21 into vehicle: • Position pole support assembly between seat base mount and floor of vehicle • Align holes in pole support assembly with holes in seat base. • Loosely attached factory seat bolts that were removed during subassembly. • Mount side support brace to threaded rod located on pole support assembly using a 5/16-18 Nylock nut • Mount side support brace to vehicle using H” x 1” Hex head lag bolts. A 3/16” pilot is required. Note: When mounting side support brace to flo

Havis-Shields Silver Billet Telescoping Computer Mounts C-PED Series

downloaded: 3File size: 159 kb    Manafacture: Havis-Shields  
Category: Optical Devices

Determine location to obtain both. • With offset bracket positioned against flat surface, (i.e., console, divider wall, etc.), mark and drill 5/16” hole at location of bolt on offset bracket. • Bolt offset bracket to “flat surface” using a fender washer and 5/16” nut. • Bolt C-PED1612 to floor of vehicle using /” x 1” -1 /” hex head lag bolts, depending on particular vehicle application. • Mount optional laptop mounts (C-3090 series), monitor mounts (C-3522), keyboard mounts (C-3329) or tilt

Havis-Shields PT-VIDEO-MDVR

downloaded: 4File size: 1 mb    Manafacture: Havis-Shields  
Category: Security Systems

, ROME, GA. 30165 TOLL FREE: (800) 242-0146 DIRECT: (706) 232-0146 FAX: (706) 232-7617 LIMITATION OF LIABILITY THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS; HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES. WARNINGS AND CAUTIONS TO REDUCE THE RISK OF FIRE OR ELEC

Havis-Shields PKG-DS-PAN-412-2

downloaded: 0File size: 3 mb    Manafacture: Havis-Shields  
Category: Computer Accessories

10 Related Products Havis offers a wide variety of accessory products specifically for use with the DS-PAN-410 Series Docking Station. For more information or to order, please visit LPS-103 120W Power Supply External power supply and cable for Panasonic CF-53 Toughbooks with cigarette lighter adaptor. DS-DA-410 Screen Stiffener Secure your laptop screen to prevent excess wear and reduce vibration while in use. DS-DA-207 Card Reader Mounting Bracket Mount an E-Seek Model 250 card reader to the si





Category