Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Hobart Welding Products XTV

downloaded: 4File size: 436 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

3. Reinstalling auto.darkening lens assembly . Gently place auto. darkening lens in front of helmet. (Be careful not to drop lens.) Install front lens cover with gasket. Grasp front lens holder and slowly insert the six retaining pieces into front of helmet. (Make certain you gently squeeze the outside edges of the front lens holder while inserting tabs into helmet.) From the inside of helmet, gently push the retaining tabs in to secure the front lens holder in place. Page 7 SECTION 4 . BATTERY

Hobart Welding Products XTP

downloaded: 5File size: 436 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

#13 Use the shade chart below to select proper shade control setting based on your welding process. We recommend starting at shades 12 or 13 and adjust lighter based on the welding application and personal preference. Application Welding Arc Current in Amperes Protective Shade No. Stick Electrodes Less than 40 40.80 80.175 175.300 #9 #10 #11 #12 . #13 MIG Less than 100 100.175 175.300 #10 #11 #12 . #13 Gas Tungsten Arc Welding (TIG) Less than 50 50.100 100.200 200.300 #10 #11 #12 #13 Page 5 Sens

Hobart Welding Products XTF

downloaded: 2File size: 436 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

READ BEFORE USING . . . . . . . . . . . . . . . . . . . . SECTION 2 . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . SECTION 3 . OPERATING INSTRUCTIONS . . . . . . . . . . . . . . SECTION 4 . BATTERY REPLACEMENT . . . . . . . . . . . . . . . . SECTION 5 . MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 6 . TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . SECTION 7 . LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . SECTION 8 . REPLACEMENT

Hobart Welding Products TS 400

downloaded: 11File size: 3 mb    Manafacture: Hobart Welding Products  
Category: Welding Systems

ALLGEMEIN ---------------------------------------- Dateioptionen: Kompatibilitat: PDF 1.4 Fur schnelle Web-Anzeige optimieren: Ja Piktogramme einbetten: Ja Seiten automatisch drehen: Zusammen pro Datei Seiten von: 1 Seiten bis: Alle Seiten Bund: Links Auflosung: [ 600 600 ] dpi Papierformat: [ 652 624 ] Punkt KOMPRIMIERUNG ---------------------------------------- Farbbilder: Downsampling: Ja Berechnungsmethode: Bikubische Neuberechnung Downsample-Auflosung: 600 dpi Downsampling fur Bilder uber:

Hobart Welding Products STICKMATE OM-949

downloaded: 0File size: 842 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

. Keep your head out of the fumes. Do not breathe the fumes. . If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases. . If ventilation is poor, wear an approved air-supplied respirator. . Read and understand the Material Safety Data Sheets (MSDSs) and the manufacturer’s instructions for metals, consumables, coatings, cleaners, and degreasers. . Work in a confined space only if it is well ventilated, or while wearing an air-supplied respira

Hobart Welding Products STELLAR AT OM-2208

downloaded: 1File size: 817 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

6 Minutes Welding 4 Minutes Resting 2-2. Duty Cycle And Overheating Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, output stops, a Help message is displayed (see Section 5-2), and cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or voltage, or duty cycle before welding. Exceeding duty cycle can damage unit and void warranty. 60% Duty Cycle Overheating 0 15 A or V OR Minutes Reduce Duty Cycle sduty1 5/95 / S

Hobart Welding Products STELLAR AT OM-180 670Q

downloaded: 0File size: 808 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

. . . . . . . . . . . . . . . . . . . . 1 ... 10. . . . . . . . . . . . . . . 187146 . . BRACKET, mtg filter board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 11 . . . . . . . . . . . . . . . 179276 . . BUSHING, snap-in nyl 1.000 ID x 1.375mtg hole. . . . . . . . . . . . . . . . . . . 2 ... 12. . . C5,6 R1 . . . 175 194 . . RESISTOR/CAPACITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 13. . . . RT1,2 . . . . 173632 .

Hobart Welding Products SPOOL GUN 3545-20

downloaded: 0File size: 140 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

#186 413 For .030/.035 in (0.8/0.9 mm) wire. Push Roll (1) #199 732 For .023 in (0.6 mm) wire. #186 414 For .030/.035 in (0.8/0.9 mm) wire. Consumables For Spool Gun 3545-20 Note: Spool Gun 3545-20 shipped with (3) .035 in and (3) .047 in contact tips. Contact Tips (5 per package) #199 387 For .030 in (0.8 mm) wire. #199 388 For .035 in (0.9 mm) wire. #199 389 For .047 in (1.2 mm) wire. Nozzle #199 386 Drive Roll (1) #186 413 For .030/.035 in (0.8/0.9 mm) wire. #199 396 For .047 in (1.2 mm) wire

Hobart Welding Products SPOOL GUN 3035-20

downloaded: 2File size: 140 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

These reliable, yet economical guns provide 20 ft (6.1 m) of cable and gas hose for extended reach. The 3035-20 and 3545-20 spool guns feature easily accessible drive rolls with a screw-style tension adjustment and smooth feeding of aluminum, steel and stainless steel wires Comes Complete With: 20 ft (6.1 m) cable and gas hose Threaded nozzle and contact tips Spool gun conversion kit consisting of control switch and gas diverter valve Enclosed wire spool compartment with internal spool hub tensi

Hobart Welding Products Panther HD Integral Driver and Power Supply

downloaded: 0File size: 197 kb    Manafacture: Hobart Welding Products  
Category: Welding Systems

REV101805 ELECTRICAL SPECIFICATIONS Input Voltage ....................................................................90 to 128 VAC or optional 180 to 264 VAC, 50/60 Hz Drive Current Per Phase ............................................................................2 to 10 Amps Peak (Max 7 Amps RMS) Isolated Logic Inputs................................................... Step Clock, Direction, Enable, Reset, Microstep Resolution 0–3 Step Frequency (Max) .......................................





Category