Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Ives Offset Top Pivot 7226/26F

downloaded: 0File size: 26 kb    Manafacture: Ives  
Category: Doors and Windows

Determine pivot location using dimensions on reverse side. The pivots are non-handed. To determine hand of door and proper pivot position, see diagrams above. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door or metal frame. Locate and drill pilot holes for #14 wood screws for wood door or wood frame. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 3. Loosen set screw in pin leaf with 3/32” Allen wrench provided and remove pivot pin. 4. Use 5/32” Allen wr

Ives Offset Top Pivot 7222

downloaded: 0File size: 23 kb    Manafacture: Ives  
Category: Doors and Windows

Follow all instructions carefully. For questions contact Technical Support at 1-888-371-7331. I*"7 Ingersoll Rand 13103 Rev. 4 © 2006 Ingersoll-Rand Company Limited Security Technologies NOTE It is very important for installer to verify that intermediate pivot point lines up with center line of top and bottom pivot points before final installation. Both door and frame pivot leafs located from face of door. Intermediate pivot should be evenly spaced between top and bottom pivots. Heel edge of

Ives Offset Top Pivot 7215/15F

downloaded: 1File size: 26 kb    Manafacture: Ives  
Category: Doors and Windows

Determine pivot location using dimensions on reverse side. The pivots are non-handed. To determine hand of door and proper pivot position, see diagrams above. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door or metal frame. Locate and drill pilot holes for #14 wood screws for wood door or wood frame. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 3. Loosen set screw in pin leaf with 3/32” Allen wrench provided and remove pivot pin. 4. Use 5/32” Allen wr

Ives Offset Top Pivot 7212

downloaded: 0File size: 26 kb    Manafacture: Ives  
Category: Doors and Windows

Determine pivot location using dimensions on reverse side. Be sure to properly locate and mark center point of the jamb leaf spindle. Care must be taken to ensure that jamb leaf is completely level. Place level against jamb leaf surfaces as shown in Figure 1. The bottom pivot set is handed. Hand of pivot must match hand of door. To determine hand of door, see diagrams above. Locate, drill, and tap 1/4-20 mounting holes for metal door or metal frame. Locate and drill pilot holes for #14 wood scr

Ives Offset Jamb Mount Top Pivot 7212V

downloaded: 0File size: 22 kb    Manafacture: Ives  
Category: Doors and Windows

Determine pivot location using dimensions on reverse side. The pivots are handed. To determine hand of door and proper pivot position, see diagrams above. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door or metal frame. Locate and drill pilot holes for #14 wood screws for wood door or wood frame. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 3. Loosen set screw in pin leaf with 3/32” Allen wrench provided and remove pivot pin. 4. With door in open posi

Ives Offset Intermediate Pivot 7212/12V

downloaded: 1File size: 23 kb    Manafacture: Ives  
Category: Doors and Windows

Determine pivot location using dimensions on reverse side. The pivots are handed and must match hand of door. To determine hand of door and proper pivot position, see diagrams above. Install top and bottom pivot sets before installing intermediate pivot. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door. Locate and drill pilot holes for #14 wood screws for wood door. Then hang door. 3. Open door about 90°. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 4

Ives Mortise Bolt S48

downloaded: 1File size: 23 kb    Manafacture: Ives  
Category: Doors and Windows

Our commitment to quality makes IVES a name you can trust. MORTISE BOLT FOR USE ON DOORS FOR ADDED SECURITY. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, W, W, VV drill bits, Phillips screwdriver pencil and chalk. L Position wdt approximately 45* to 60" from bottom of door on center of door eage. Mark and drill Vi«' hole 2W deep (A). 2. DrillW hole W deep and IV/ from edge of door (B). 3. Place bolt in brfe (A) insert knob shaft in hole (B) to align with (C). Mark, drill and secure t

Ives Mail Slot Sleeve C602

downloaded: 0File size: 29 kb    Manafacture: Ives  
Category: Doors and Windows

Secure with two screws provided. 3. Replace and secure front plate over sleeve. For New Mail Slot Installations: 1. Follow mail slot installation instructions. 2. Insert sleeve through door cutout and secure. 3. Secure front plate over sleeve. © 1993 H.B. IVES, Wallingford, CT 06492

Ives Mail Slot Sleeve C600

downloaded: 0File size: 29 kb    Manafacture: Ives  
Category: Doors and Windows

Our commitment to quality makes IVES a name you can trust. d MAIL SLOT SLEEVE NOS. C600, C602 FOR USE ON EXTERIOR DOOR OF HOMES, CONDOMINIUMS, APARTMENTS AND OFFICES. COVERS ROUGH EDGES OF CUTOUT ON SOLID OR HOLLOW DOORS AND PREVENTS MAIL FROM FALLING INTO HOLLOW CORE DOORS. NO. C600 Fits IVES mail slots nos. 626,627,628, 629 or standard mail slots requiring a 77/ " x 29/ " cutout. Id 5Z NO. C602 Fits IVES mail slots nos. 618,619,623, 624 or standard mail slots requiring an 8V|6" x 23/g" c

Ives Magnetic Catch 327

downloaded: 0File size: 24 kb    Manafacture: Ives  
Category: Doors and Windows

Our commitment to quality makes r\'ES a name you can trust. SUPER-MITE® MAGNETIC CATCH DUAL TRIPLE POLE FOR USE ON LARGE CABINET AND FULL LENGTH DOORS. FEATURES HEAVY DUTY DESIGN WITH EXTRA STRENGTH HOLDING POWER. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, Vis" drill bit, Phillips screwdriver, awl or pencil. FOR SINGLE DOOR APPLICATION (Illustration 1): 1. Po'sition case (A) on top corner or side of door frame. 2. Mark, drill pilot holes in center of elongated holes (B) and secur





Category