Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Meyer WOODCHUCK 526

downloaded: 0File size: 515 kb    Manafacture: Meyer  
Category: Electric Heaters

There is some doubt among wood heat experts as to whether use of barometric draft regulators is wise. Draft regulators limit the draft-the suction pulling air into the appliance. A pivoted, counter-balanced flap is pulled open by the draft when the draft reaches a critical amount (figure 10). This permits air to enter the chimney, thus preventing the draft in the appliance from rising any higher. Use of draft regulators with oil-fired equipment is common. One objective is to keep the oil flame f

Meyer WOODCHUCK 4000

downloaded: 0File size: 515 kb    Manafacture: Meyer  
Category: Electric Heaters

Now you are ready to light a fire. BURNING WOOD IN YOUR WOODCHUCK 1. Adjust draft channel selector, figure 5, to appropriate fuel setting on model 2900/4000. On Model 526 with manual draft, open it. Place several pieces of crumpled paper in the center of your Woodchuck. Criss-cross a couple of handfuls of dry kindling wood 3/4" thickness, then several small dry pieces of firewood. Ignite the paper and close the door. Do not attempt to open the door immediately after igniting the fire. There coul

Meyer WOODCHUCK 2900

downloaded: 0File size: 515 kb    Manafacture: Meyer  
Category: Electric Heaters

WOOD/COAL FURNACES Phone 715/654-5132 Fax 715/654-5513 07/97 INTRODUCTION Dear Woodchuck Owner, Congratulations on your purchase of a Woodchuck heating appliance. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected a Woodchuck. Pride in craftsmanship and engineering have made your Woodchuck the finest heating appliance available today. Solid fuels are abundant and inexpensive. Wood is our only renewable source of fuel and conservative estimates p

Meyer V- MAX 3954

downloaded: 0File size: 4 mb    Manafacture: Meyer  
Category: Garden Tools

Model V-Max —30— RH AUGER DRIVE, FINAL REDUCTION KEY PART NO. DESCRIPTION 1 33-0025 2-1/2" Retaining Ring 2 910-0064 Welded Sprocket Assy, LH, 80/60 x 120/9 3 910-0028 Auger Sprocket 120B33, Splined-Nonshear 910-0101 Shear Sprocket Assy. 120B33 831-5020-1.75 .-20 x 1-3/4" Allen Head Cap Screw Grade 8 884-5020 .-20 Top Locknut Grade 8 831-5618-1.75 9/16-18 x 1-3/4" Allen Head Cap Screw Grade 8 884-5618 9/16-18 Top Locknut Grade 8 4 813-3118-Z 5/16" Regular Nut 5 933-3804 5/16"x4" Full Thread Eye

Meyer V- MAX 3245

downloaded: 2File size: 4 mb    Manafacture: Meyer  
Category: Garden Tools

LONG HAY OR STRAW MUST CONTAIN MANURE IN ORDER TO BE SPREAD. FAILURE TO COMPLY MAY DAMAGE THE DRIVETRAIN AND VOID THE WARRANTY. The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition. The factors that contribute most to differing patterns will be moisture content and the amount and length of bedding material. For most typical conditions, the spread pattern should be unif

Meyer V- MAX 2636

downloaded: 0File size: 4 mb    Manafacture: Meyer  
Category: Garden Tools

5,368,236 5,501,404 DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD. Manufactured by County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 E-mail: sales@meyermfg.com TABLE OF CONTENTS MANUFACTURER’S WARRANTY .........................................................................................................................3 INTRODUCTION..........................................................................

Meyer 8865

downloaded: 0File size: 3 mb    Manafacture: Meyer  
Category: Garden Tools

Check regularly for any observable oil leakage. If oil leakage is excessive, replace required input/output shaft oil seals. Use ONLY EP #80-90 wt. gear lube oil or an equivalent in corner box, only Lighter weight gear lube oil may be used in temperatures lower than 20°F. Change oil in the gearboxes after the first season of use and regularly thereafter. L13 Grease (1) brass bushing supporting the rear shaft of the 3rd auger assembly. This zerk is located on the left rear corner of the tank above

Meyer 8720

downloaded: 44File size: 3 mb    Manafacture: Meyer  
Category: Garden Tools

PATENT NUMBER 5,368,236 5,501,404 8865 SPREADER 8720 SPREADER DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD MANUFACTURED BY County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425-0405 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 E-mail: sales@meyermfg.com 12/06 TABLE OF CONTENTS INTRODUCTION.................................................4 SAFETYPRECAUTIONS.............................................5 SAFETYFIRST...........................................





Category