Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Nuvo REMOTE IPOD RECEIVER NV-RIPR1

downloaded: 6File size: 234 kb    Manafacture: Nuvo  
Category: Speakers & Subwoofers

The included dock can be located in any zone of the house and requires just a single Cat5 connection from the dock to the NV-RJ45P component located in the wall. Additionally, a single Cat5 run from the back of the RJ45P to the back of the NV-RIPR1 iPod receiver component located with the Grand Concerto ,:1"’: transmits power, audio signal and metadata. The Grand Concerto EZ Port acts as a communication hub enabling seamless control of the of the Grand Concerto Control Pads throughout the home

Nuvo NV-WIPS

downloaded: 2File size: 599 kb    Manafacture: Nuvo  
Category: Speakers & Subwoofers

If the NV-WIPS does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced rad

Nuvo NV-I8DEZP

downloaded: 0File size: 150 kb    Manafacture: Nuvo  
Category: Speakers & Subwoofers

NÜVÖ The Sound of LiVing NV-WIPS Wireless iPod Dock System The included 3.5mm to RCA stereo audio cable provides audio to the Grand Concerto System as one of its six sources. A rotary switch at the iPod dock and receiver set a specific source address (1-6) for the Grand Concerto System NuVoNet communication. m "Sir;1 NOVS 1 PSK' o T 0“ The included Cat5 network cable enables complete iPod communication with the Grand Concerto System. Each of the Grand Concerto's zone Control -

Nuvo 500

downloaded: 9File size: 5 mb    Manafacture: Nuvo  
Category: Water Dispensers

Other problems may derive from improper cabinet assembly, power interruption or surge, low line voltage (less than your unit rating of 105V or 240V), or failure to clean the unit regularly (see illustration below). The following may help you determine what the problem may be; what steps you can take to correct it, and what further steps may be required. Additional Trouble-Shooting information and downloadable documents are available in the “Support” area of our web site: Cleaning the coil IMPORT

Nuvo 250

downloaded: 2File size: 5 mb    Manafacture: Nuvo  
Category: Water Dispensers

AREA FOR ASSEMBLING YOUR WINE CELLAR Choose a clear 12’ by 12’ area with a level floor and carpeting to help reduce scratching of surfaces. 3. TOOLS * Hex wrench (included) * Phillips screwdriver * Carpenter’s level * Helper or two is strongly recommended 4. TEST THE COOLING UNIT Plug it in for a few minutes on a table top, to verify that controls and display are functional, and that the unit is producing cool air after a few minutes of operation. Note that the electronic controller has a one-mi

Nuvo 220

downloaded: 0File size: 4 mb    Manafacture: Nuvo  
Category: Water Dispensers

PRESS and HOLD until buzzer sounds in 5 seconds The new value will be memorized and the controller will reset automatically. PRESS and HOLD while holding PRESS and RELEASE Wait 5 seconds USE or for each degree of offset 57. 56. 70. 57. 57. 57. 57. 58. 57. 56. 57. 14. 57. 57. 57. F0 F0 F1 F0 -1 TO DISPLAY: TO MODIFY SET TEMPERATURE (range is 52-64.F): TO CHAANGE FROM .F to .C: or .C to .F TO CALIBRATE: NOTE: A negative offset will result in a warmer cabinet and a positive offset will result in a

Nuvo 110

downloaded: 0File size: 4 mb    Manafacture: Nuvo  
Category: Water Dispensers

(See troubleshooting for details.) G. Always remove all bottles before relocating your wine cellar. HARDWARE KIT C B A Cam Cap x 20 (x24)* Hex Wrench x 1 Hex Bolt x 14 D F E Leg x 4 Cam x 20 (x24)* Cam Pin x 20 (x24)* H G In Cooling Unit Box Hex Bolt (Flange) x 2 Panel Insulation Strip x 1 *NOTE : Hardware quantities for Model 220 are indicated in parenthesis. STEP 1 : PANEL PREPARATION CAUTION : 1. Watch for sharp staples on boxes. 2. DO NOT STEP ON PANELS 3. The manual will give a recommended





Category