Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Omega Vehicle Security SSHB

downloaded: 0File size: 321 kb    Manafacture: Omega Vehicle Security  
Category: Electric Heaters

Use a medium to hard roller to Do not wrap the heater over heater. © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, MOUNTING YOUR HEATING BLANKET Installation of heater using factory supplied Pressure Sensitive Adhesive (PSA): 3. Peel off the release film [Figure A] and then press the heater onto the surface of the item being heated using a medium to hard rubber roller [Figure B]. Ensure blanket is making intimate contact wit

Omega Vehicle Security SRMU

downloaded: 0File size: 321 kb    Manafacture: Omega Vehicle Security  
Category: Electric Heaters

• Never operate a heater without an appropriate heat sink (device being heated is considered a heat sink). • Do not operate heater above rated temperature value. • Fasten heater to device using approved methods only. • Do not repair damaged or faulty heaters. • Do not crush or apply severe physical stress on heater or cord assembly. • Disconnect heater when not in use. • SEPHB series: the metal enclosure must not support more than 10lbs (4.5kg). Failure to observe these result in personal injury

Omega Vehicle Security SH73343

downloaded: 1File size: 483 kb    Manafacture: Omega Vehicle Security  
Category: Electric Heaters

Description Compact, safe and versatile heating unit for heating air or inert gas up to 1400°F. The SH-Series is available in wattages from 6kW to 36kW, and can be use with compressed air or a regenerative blower. The SH heater is designed for closed-loop temperature control, with a solid-state relay or phase angle fired SCR power control. Sensors inside the heater sense both element temperature and inlet air temperature and limit heater voltage and prevent element burnout if airflow is suddenly

Omega Vehicle Security SEPHB Series

downloaded: 0File size: 321 kb    Manafacture: Omega Vehicle Security  
Category: Electric Heaters

2 Important Safety Instructions……………...................... 3 Prior to Installation........................................................ 4 Mounting Your Heating Blanket..................................... 5 Connecting Your Heating Blanket to a Power Source... 6 Troubleshooting Guide.................................................. 7 Warranty........................................................................ BACK Return Requests / Inquires........................................... BACK

Omega Vehicle Security PX792 Series

downloaded: 1File size: 293 kb    Manafacture: Omega Vehicle Security  
Category: Water and Air Pumps

OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. WARNING: These products are not designed for use in, and should not be used for, patient-connected applications. PX

Omega Vehicle Security PX791

downloaded: 0File size: 293 kb    Manafacture: Omega Vehicle Security  
Category: Water and Air Pumps

Refer to Figure 1. The loop supply voltage vs. loop resistance shows the minimum supply voltage (Vmin) required for a given loop resistance (RLOOP). Excitation (Ratiometric Output Only) For proper operation a voltage within the range of 5 to 10 Vdc must be applied between the transducer’s supply terminals. Noise For minimum noise susceptibility, avoid running the transducer’s cable in a conduit that contains high current AC power cables. Where possible avoid running the cable near inductive equi

Omega Vehicle Security PX548

downloaded: 1File size: 101 kb    Manafacture: Omega Vehicle Security  
Category: Other Tools

The sensor should be put in its normal operating position (vertical or horizontal). Remove the cover to gain access to the zero and span adjustment potentiometers. Zero adjustment uDepending on the model, set the zero adjustment to: 0.00 V, 4.00 mA or 12.00 mA. uSpan adjustment is carried out with the required span pressure applied to the + uDepending on the model, set the span adjustment to: 5.00 V, 10.00 V or 20.00 mA. uRelease the pressure. Completion Check the output at zero pressure and if

Omega Vehicle Security PTC900

downloaded: 0File size: 1 mb    Manafacture: Omega Vehicle Security  
Category: Time Clocks

The meter configuration data can be saved to a file for later recall. Once the meters have been initially configured, the parameter list may be locked out from further modification entirely, or the setpoint, timer start/stop values, counter start/stop values, RTC time SET, and Display Intensity can be made accessible. This lockout is possible through a security code or user input. The meters have been specifically designed for harsh industrial environments. With a NEMA 4X/IP65 sealed bezel and e

Omega Vehicle Security PPA100

downloaded: 0File size: 64 kb    Manafacture: Omega Vehicle Security  
Category: Water and Air Pumps

Combined with one of our pressure calibrators, the PPA100 makes a complete Pressure/ Vacuum Calibration System. Operation The drawing shows the operation of the controls on the PPA100. The pump is designed for use with ambient air only. Pump Valve Assembly Cleaning Instructions Occasionally, the PPA100 may not work properly due to dirt or other contamination of the internal valve assembly. Use the following procedure for cleaning the valve assembly. 1. Using a small screwdriver, remove the 2 val

Omega Vehicle Security PHCN-410

downloaded: 3File size: 244 kb    Manafacture: Omega Vehicle Security  
Category: Electric Heaters

Call toll free in the USA and Canada: 1-800-622-2378. FAX: 203-359-7811; International: 203-359-1660. FAX: 203-359-7807. BEFORE RETURNtNG ANY PRODUCT(S) TO OMEGA, YOU MUST OBTAIN AN AUTHORtZED RETURN (AR) NUMBER FROM OUR CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESStNG DELAYS). The assigned AR number should then be marked on me outside of the return package and on any correspondence. FOR w RETURNS. please have the fol-FOR BREPAIRS OR CALIBRATION. towing information available BEFORE cont





Category