Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Sanus Systems VP1

downloaded: 0File size: 6 mb    Manafacture: Sanus Systems  
Category: Projectors

All rights reserved. Sanus is a division of Milestone. All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners. VP1 (6901-002053 <00>) Wood Ceiling Joists 13mm (1/2 in.) 5.5 mm (7/32 in.) Enggliisshh DDaannsskk Page 4 Side 34 Francais Svenska Page 18 Deutsch Seite 20 Espanol Pagina 22 Portugues Pagina 24 Nederlands Pagina 26 Italiano Pagina 28 ........ ...... 30 Norsk Side 32 Sidan 36 Русский Стр. 38 polski Strona 40 Cesky Strana 42 Turk

Sanus Systems VMCC1

downloaded: 0File size: 6 mb    Manafacture: Sanus Systems  
Category: Kitchen-ranges

Sanus Systems VMCC1

downloaded: 0File size: 17 mb    Manafacture: Sanus Systems  
Category: Kitchen-ranges

The VMCC1 is designed to mount a center channel speaker below a Sanus VMSA, VMAA, VMAA18, VMAA26, VMDD or a VMDD26 Flat Panel Wall Mount. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing

Sanus Systems VISIONMOUNT VMCA9

downloaded: 0File size: 2 mb    Manafacture: Sanus Systems  
Category: Time Clocks

The VMCA9 ceiling plate is designed to attach to an NPT 1-1/2 in. threaded pipe. The VMCA9 will support a maximum weight of 226.8 kg (500 lbs). - CAUTION - Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper assembly may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the assembly, contact Sanus Systems Customer Service or call a qualified contractor. Sanus Systems is not liable for

Sanus Systems VISION MOUNT VMPO

downloaded: 0File size: 739 kb    Manafacture: Sanus Systems  
Category: Kitchen Utensil

It can also be used with a VM200 for tilting LCDs or a VMPL50 for Plasmas. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased thro

Sanus Systems TELEVISION TURNTABLES TV32

downloaded: 0File size: 489 kb    Manafacture: Sanus Systems  
Category: Televisions

When Using the TV27 or TV32 use the rear Pilot Hole. Step 3: Insert the Plastic Dowels into the larger holes in the Support Pillar as shown in the Diagram on the right. Gently tap the Plas- tic Dowels in with a hammer if needed. Repeat step for the other Support Pillar. Step 4: Thread the Allen Bolts up through the Base of the TV-VCR Kit, and into the corresponding holes in the Support Pillar. Tighten Allen Bolts with the provided Allen Key until they are tight. Step 5: Add the TV Turntable to t

Sanus Systems TELEVISION TURNTABLES TV27

downloaded: 0File size: 489 kb    Manafacture: Sanus Systems  
Category: Televisions

Supplied Parts: (1) Television Turntable Supplied Parts: (1) Self Adhesive Protective Feet (pad of 4) Diagram 1Step 1: Position the Turntable so the black nylon swivel is facing up. Locate the circles at the end of each spoke. Next, place a Adhesive Foot inside each circle, as shown in Diagram 1. NOTE: If you are going to use the optional TV-VCR Kit, Proceed to the instructions for those at the bottom of the page, otherwise, proceed to Step 2. Step 2: Flip the Turntable over and place it in the

Sanus Systems TELEVISION TURNTABLES TV20

downloaded: 0File size: 489 kb    Manafacture: Sanus Systems  
Category: Televisions

Paul, MN 55113 800.359.5520 7.6.04 TVTurntable (sold separate) SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar Support PillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillar BaseBaseBaseBaseBaseBaseTV Turntable (sold separate) Pillar SupportPillar SupportPillar Support Base Step 1: Remove the swivel from the TV Turntable by removing the Phillips Screw in the center of t

Sanus Systems TELEVISION TURNTABLES TV13

downloaded: 1File size: 489 kb    Manafacture: Sanus Systems  
Category: Televisions

Please check carefully to make sure there are no miss- ing or defective parts. Never use defective parts. Improper assembly may cause damage or injury. If you do not understand these directions, or have any questions about this assembly please contact Sanus at 800.359.5520 or We can quickly assist you with installation questions and missing or damaged parts. Supplied Parts: (1) Television Turntable Supplied Parts: (1) Self Adhesive Protective Feet (pad of 4) Diagram 1Step 1: Position the Turntab

Sanus Systems TELEVISION TURNTABLES TV-VCR

downloaded: 0File size: 489 kb    Manafacture: Sanus Systems  
Category: Televisions

Phillips Screw Bottom ofBottom ofBottom of TurntableTurntableTurntableTurntableTurntableTurntableTurntablePhillips Screw TV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit Base Front Pilot Hole Rear Pilot Hole Plastic DowelsLarger HoleLarger HoleLarger HoleLarger HoleLarger HoleLarger HoleLarger Hole Support Pillar Top of TV-VCR BaseTop of TV-VCR BaseTop of TV-VCR BaseTop of TV-VCR Base Nylon Swivel is Allen Bolts Located on the Bottom Top of TVTurntableTop of TVTurntableTop





Category