7. Cycle Set to your preferred value for the digit. 8. Push Mode to select. 9. Repeat steps 7 and 8 to select the other three digits. 10. Push Mode. 10. Cycle Set for the first digit of Odometer. 11. Push Mode to select the digit. 12. Repeat steps 10 and 11 to select the other digits of Odometer. The computer returns to current speed display. Setting the computer To set Clock 1. Cycle Mode to CLK. 2. Hold Mode. 3. Cycle Set to 12 or 24 hour clock. 4. Push Mode to select clock. 5. Cycle Set to th
Heart rate strap s not contact ng sk n. Mo sten and repos t on. 9 Troubleshoot ng 19 06 Incite ACH 07_13.indd 7/14/06 7:26:06 AM rePlACIng THe BATTery If the computer is giving erratic information, a computer or sensor battery may be running low on power (normally accompanied by the low battery icon, Figure 17). Replace the batteries whenever the computer malfunctions, or every 6 months. Take an old battery to the store with you, but this is the generic description for the proper battery: ACH co
To set the units 1. Cycle Mode to MAX (Figure 12). 2. HoldSet• KMH or MH flashes. 2 Easy setup (reSet) CLKTMEAVGMAXTRPODOMHMode Set Mode Set 3. Cycle Mode CLKTME ODO MAXTRPAVG MPH F Figure 3- oDo screen MH and KMH interchange on the screen. 4. Push Set• to select. The temperature icon display. 5. Cycle Mode to C or F 6. Push Set• to select. The computer returns to the start screen. To set the odometer 1. Cycle Mode to ODO (Figure 13). 2. HoldSet• 5-digit odometer value appears with first digit f
Selecting the custom value 4-digit number There are two methods for Table 3- Custom wheel size codes selecting the custom wheel size value: • Select a value from Table 3, Custom wheel size codes. • Do a rollout test to measure the circumference of your wheel (page 24). To set the computer 1. Cycle Mode to TME. 00 x 20 2086 26 x .5 20 0 00 x 23 2096 26 x .90 2045 00 x 25 2 05 26 x .95 2050 00 x 28 2 36 26 x 2.0 2055 00 x 32 2 55 26 x 2. 2068 00 x 35 2 68 26 x 2.2 20 5 00 x 38 2 80 Custom 0000 -
If you do not understand the information in this manual, or you have a question about your Incite computer that this manual does not cover, consult your Trek dealer. If you have a question or problem that your Trek dealer can’t handle, contact us at: Trek Bicycle Corporation Attn: Customer Service 801 W. Madison Street Waterloo, Wisconsin 53594 trekbikes.com (920) 478-4670 CONTENTS Safety and general guidelines............................... i Functions...........................................
2. Wrap the wire around the front brake cable, diverting the determined amount. 3. Continue routing the wire, either by wrapping around the fork or frame tube, or attach the wire to the fork or frame tube with electrical tape. 4. As needed, solidify the wire attachment with either nylon ties or electrical tape. Installation Attaching the sensor The magnet must pass across the line on the sensor (Figure 9). To install the sensor 1. Align the sensor with the magnet. 2. Orient the sensor so that th
We recommend setting the speed scale and wheel circumference before installing the computer. Precautions Remember to watch the road or trail while riding. Watching your bicycle computer makes it difficult to see upcoming obstacles. Awareness of potential road, trail or traffic problems should be your main concern. Main Unit/Accessories 8 1 Contents: 1. Main Unit 5. Magnet 9. Mounting Clamp 2. Bracket 6. Wire Securing Tape 10. Rubber Pad for Clamp 3. Wire 7. Zip Tie 4. Wheel Sensor 8. Bracket Rub
Please read this manual carefully and save it for future reference. If you do not understand the information in this manual, or you have a question about your Incite 9i computer that this manual does not cover, consult your Trek dealer. If you have a question or problem that your Trek dealer can’t handle, contact us at: Trek Bicycle Corporation Attn: Customer Service 801 W. Madison Street Waterloo, Wisconsin 53594 trekbikes.com © Copyright Trek Bicycle Corporation (920) 478-4670 2006 All rights