Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Wayne-Dalton TORQUEMASTER PLUS 9300

downloaded: 0File size: 5 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

Repeat for other section(s) except top section. IMPORTANT: PUSH & HOLD THE HINGE LEAFS AGAINST SECTION WHILE SECURING WITH (2) 1/4” -14 x 5/8” SELF TAPPING SCREWS. END AND INTERMEDIATE HINGES HAVE (2) SCREWS. NOTE: Install lock at this time (sold separately) see Side Lock installation instructions on page 25. 8 Power Drill 7/16” Socket Driver 9 Top Bracket Slide To install the top bracket slide, align the slots in the top bracket slide with the set of holes under the top sections u-bar. Loosely

Wayne-Dalton TORQUEMASTER 9700

downloaded: 2File size: 10 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

This will prevent the door from raising or lowering while installing the rear support. Using perforated angle, 2” lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”-18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door. ^WARNING! KEEP HORIZONTAL TRACK PARALLEL AND WITHIN 3/4” OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN

Wayne-Dalton TORQUEMASTER 6100

downloaded: 1File size: 12 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

If the system engages with the door in the open position, personal items that are left unattended in the garage or home are at risk to theft. To insure the safekeeping of these items, close the garage door. Typical signs of an engaged system: Single spring system: Visually inspect the TorqueMaster® Plus right hand end bracket to confirm that the system has engaged (see illustration). If the system is engaged then the door will not close. If the opener force settings were properly set during the

Wayne-Dalton TORQUEMASTER 5500

downloaded: 0File size: 10 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

IF THE INSERT SHEET INSTRUCTIONS ARE NOT INCLUDED, CONTACT WAYNE-DALTON CORP. FOR A FREE COPY. If removing an existing door, carefully follow the directions given on the insert sheet instruction in the portion titled “Removing the Old Door”. ¿^WARNING! REMOVAL OF AN EXISTING DOOR CAN BE DANGEROUS. FOLLOW INSERT SHEET INSTRUCTIONS CAREFULLY, OTHERWISE SEVERE OR FATAL INJURY COULD RESULT Begin the installation of the door by checking the opening. It must be the same size as the door. Vertical ja

Wayne-Dalton TORQUEMASTER 5140

downloaded: 0File size: 9 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

Plug the motor power cord into the opener. lEFT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED RIGhT haND END OF TORquEMasTER® sPRING TuBE RIGhT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED PluG-IN MOTOR POWER CORD MOTOR 17 Tools Needed: None Tools Needed: idrive® Installation NOTE: see idrive® main installation and owners manual for idrive® parts. IMPORTANT: RIGhT aND lEFT haND Is alWays DETERMINED FROM INsIDE ThE GaRaGE lOOkING OuT. lay the TorqueMaster® s

Wayne-Dalton TORQUEMASTER 5120

downloaded: 0File size: 9 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

NOTE: Do not tighten 1/4”-20 flange nuts to opener studs at this time. You will be instructed when to tighten them in the idrive® main installation and owners manual. Remove the temporary orange label holding the antenna wire. Straighten antenna wire and angle it 45 degrees to the right. NOTE: Do not coil the antenna wire. This will reduce the radio signal range. Power Drill 1/8” Drill Bit 7/16” Socket Driver 45 angle Antenna wire Mounting surface (Header) TOP OF DOOR SUPPORT BRACKET 1/4” X 1-1/

Wayne-Dalton TORQUE MASTER PLUS 9600

downloaded: 0File size: 909 kb    Manafacture: Wayne-Dalton  
Category: Safety Gate

Using a ratchet wrench with a 5/8” (16mm) socket (NOTE: A 3” (76mm) extension is also recommended for added clearance from the horizontal angle), wind the spring by rotating the winding shaft counter clockwise, while watching either the black tooth on the ratchet wheel or the mark on the winding shaft. Important : paw l knob must be in upper position to add/ remove required number of spring turns. After 2-3 turns, remove the ratchet wrench and adjust the cable on the left side. Ensure counterbal

Wayne-Dalton TORQUE MASTER PLUS 9400

downloaded: 0File size: 909 kb    Manafacture: Wayne-Dalton  
Category: Safety Gate

for single spring applications, there will be no left hand spring in the TorqueMaster ® spring tube assembly. lift the TorqueMaster® spring tube assembly and rest it on top of the flag angles. NOTE: Cable drum assemblies are marked right and left hand and consist of a cable drum and drum wrap. Cable drums and TorqueMaster® spring tube assembly are cam shaped to fit together only one way. Starting on the right hand side, slide the drum wrap over to access the counterbalance cable. Pre-wrap the ca

Wayne-Dalton TORQUE MASTER PLUS 9100

downloaded: 0File size: 909 kb    Manafacture: Wayne-Dalton  
Category: Safety Gate

Wayne-Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’s Manual before you attempt this installation. To avoid possible injury, read the enclosed instructions carefully before installing and operating the garage door. Pay close attention to all warnings and notes. After installation is complete, fasten this manual near garage door for easy reference. The Quick Start Guide and Installation Instructions and Owner’s Manual are available at no charg

Wayne-Dalton THERMOSPAN 125

downloaded: 0File size: 1 mb    Manafacture: Wayne-Dalton  
Category: Safety Gate

At this price point, the construction provides a substantially higher thermal efficiency than industry standard polystyrene doors. The Wayne-Dalton Thermospan Series doors are the only doors in the industry with patented, roll-formed integral struts on each section, making them the most rigid doors available. WAYNE- DALTON COMMERCIAL DOOR SYSTEMS • EXCEPTIONAL THERMAL QUALITIES (R-VALUE = 10.79, U-VALUE = 0.093) • STANDARD SIZES UP TO 16’ 2” WIDE AND 16’ 1” HIGH • COMPETITIVELY PRICED • COMMERCI





Category