Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Dakota Digital MULTI GAUGE UTV-1200

downloaded: 5File size: 130 kb    Manafacture: Dakota Digital  
Category: Time Clocks

UTV-1200 Multi Gauge for 2008 Yamaha Rhino Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience. 00000.0 Odometer 12:00A Clock (hold left switch to set) Setting clock: Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode H 0.0 Hourmeter Right switch functions Pressing the right function switch during norma

Dakota Digital LED Tail Lights LAT-NR160

downloaded: 1File size: 199 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. The housing may need to be removed from the car on the ’71-’72 Chevelle. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the screw and aluminum back plate from the back of the new LED assembly. LED assembly standard back back for ‘71-‘72 Chevelle (attached to the assembly) (packaged separately) 6. Insert

Dakota Digital PAC-3500

downloaded: 8File size: 67 kb    Manafacture: Dakota Digital  
Category: Doors and Windows

3Speeds are approximate and may vary slightly depending on application Wiring to a door lock motor. Dakota Digital RLY-2 relay pack shown. To PAC-3500Lock output. FUSED 12V POWERTo PAC-3500Unlock output. The wires between the switch and the motor will need to be cut, and the relay pack wired in between as shown. Fused 12V power. MOTORMOTORSWITCHPURPLEGREENBROWNWHITEBLUERELAYREDsmall wireGREENPACKBLUEsmall wireDUAL+12v on lock+12v on lock Indicator LEDs The green LED will turn on when the auto-lo

Dakota Digital LAT-NR261

downloaded: 2File size: 119 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

If the gasket is hard or brittle it should be replaced. 4. Now is a good time to clean or replace the lenses and housings if necessary. If the lenses are in poor condition a replacement set is recommended. MAN#650217 5. Insert the LED assembly bulb base into the tail light housing socket. 6. Place the new LED assembly into the housing so that the aluminum mounting bracket sits into the groove for the lens gasket. 7. Replace the lens gasket. The gasket will sit on top of the aluminum mountin

Dakota Digital LED Tail Lights LAT-NR362

downloaded: 2File size: 145 kb    Manafacture: Dakota Digital  
Category: Other Home Accessories

Now is a good time to clean and inspect the lenses also. If the lenses are in bad shape, a replacement set is recommended. MAN#650205 11. Push the bulb base plug and wire from the LED assembly through the light bulb hole in the back of the tail light housing. 12. While working the wire harness through the light bulb opening, place the LED assembly into the housing. The mounting plate is marked with up arrows that should point to the top of the tail light housing when the LED assembly is insta

Dakota Digital MAN #650134

downloaded: 0File size: 156 kb    Manafacture: Dakota Digital  
Category: Time Clocks

These features include: · Quartz accuracy · Night dimming feature · Very low standby power to prevent battery drain · High visibility VFD display for sunlight readability · Displays current time in 12 hour format Wiring: Clock BLACK Connect to a good ground point in the vehicle RED Connect to switched 12 volt power point (An accessory terminal will work for this) ORANGE Connect to a constant 12 volt power point (This will keep the correct time) BLUE Connect to the taillight circuit +12V when lig

Dakota Digital LED Tail Lights for 1957 Chevy Car LAT-NR210

downloaded: 0File size: 127 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

2. Remove the light bulb 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the lock nut and flat plastic back plate from the back of the new LED assembly. 6. Make sure that one wire is still going through each hole in the aluminum spacer. Insert the new LED assembly through the hole where the original bulb and connector were located. Use caution

Dakota Digital LED Tail Lights LAT-NR120

downloaded: 2File size: 140 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Remove the two screws and aluminum plate from the back of the new LED assembly. 6.Insert the new LED assembly through the hole where the original bulb and connector were. Be careful when feeding the wires throughto avoid damaging insulation. 7.Feed the wires through the larger hole in themoun

Dakota Digital LED Tail Lights for 1969 Chevelle LAT-NR310

downloaded: 1File size: 177 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

Remove the tail light housing from the vehicle. 2. Remove the bulb connector from the back of the housing. 3. Remove the 4 screws that hold the trim and lens. Remove the trim and tail light lens from the tail light housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Note that there are two different LED assemblies. One for the driver side and one for the passenger side. Select the correct assembly for the tail light housing. Remove the two locking nuts and fl

Dakota Digital LED Tail Lights LAT-NR350

downloaded: 1File size: 151 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

If the lenses are in poor condition a replacement set is recommended. 7. Make sure the housings and lenses are clean and dry. DO NOT remove backing from tape yet! Place the light diffuser onto the back of the lens. Check for proper fitment of diffuser to inside of lens and note the places where the tape touches the lens. MAN#650204 8. DO NOT remove the backing from the tape yet! Place the LED assembly in the housing. The wide black bar on the wire side of the LED assembly is marked to show wh





Category