Votes - 2, Average rating: 4 ( )

User manual Bosch, model ART EASYTRIM Accu NIMH

Manafacture: Bosch
File size: 3.13 mb
File name: 913217d4-ef2c-438c-bb53-f7a2090080a6.pdf
Language of manual:ruplsvhrukitentresfrdebgetslnlhuptskficslvltro
Free link for this manual available at the bottom of the page

manual abstract

Product Specification Trimmer ART 23 EASYTRIM ACCU/ ART 2300 EASYTRIM ACCU ART 26 EASYTRIM ACCU/ ART 2600 EASYTRIM ACCU Part number (typ) 3 600 H78 H.. 3 600 H78 J.. No-load speed [rpm] 9 500 9 000 Cutting circle [cm] 23 26 Weight (without optional extras) [kg] 1.9 2.0 Serial Number See serial No 14 (rating plate) on machine. Battery type NiMH NiMH Battery order number 2 607 335 699 2 607 335 699 Battery Voltage [V] 14.4 14.4 Battery rating [Ah] 1.5 1.5 Charging time (empty battery) [h] 3 - 5* 3 - 5* Battery charger AL 1404 AL 1404 Order number 2 607 225 .. 2 607 225 .. Charging current [A] 0.4 0.4 Allowable charging temperature range [°C] 0 – 45 0 – 45 *Charging time based on a battery charger input voltage of 230 V. Intended Use Introduction Delivered Items Operating Controls 13 • F016L70 457 • 06.12 English - 3 Charging Procedure The charging procedure starts as soon as the mains plug is plugged into the socket and the battery 9 is inserted into the charging compartment 11. The green LED 12 is not a charge control indicator! When the green LED is lit, it indicates that a charging current flows. After the end of the charging process (approx. 3 h– 5 h), pull the mains plug of the battery charger from the socket and remove the battery. The battery should not be charged for longer than 5.5 hours. A temperature increase of the battery indicates that it is fully charged. Charging Advice With continuous or several repetitive charging cycles without interruption, the charger can warm up. This is not harmful and does not indicate a technical defect of the unit. A battery that is new or has not been used for a longer period does not develop its full capacity until after approximately 5 charging/discharging cycles. Leave such batteries in the charging compartment until they have clearly warmed up. A significantly reduced working period after charging indicates that the batteries are used and must be replaced. Do not connect the battery before product is completely assembled. Ensure product is assemble in the following order: Assemble trimmer shaft Push the upper shaft 4 and lower shaft 5 together until a click can be heard. Note: Once the upper and lower shaft is assembled it can not be disassembled. Ensure internal cable is not trapped or twisted. Mounting the Cutting Guard Place the cutting guard 8 on the trimmer head 6. Hook the guard onto trimmer head and push until secure fitting. Push rear of guard until secure (click). Fitting Cutting Disc/Fitting Blade Press cutting disc 15 onto drive adaptor as shown (click). Fit the blade, place the blade 16 over the pivot 17 and pull outwards until it snaps into place. Remove stones, loose pieces of wood and other objects from the cutting area. The blade continues to rotate for a few seconds after the trimmer is switched off. Allow the motor/ blade to stop rotating before switching “on” again. Do not rapidly switch off and on. Switching On and Off Press switch 1 and hold depressed. Release switch 1 for switching off. Cutting Grass Move the trimmer left and right, keeping it well away from the body. The trimmer can efficiently cut grass up to a height of 15 cm. Cut taller grass in stages. Cutting Around Trees and Bushes Carefully cut around trees and bushes so that they do not come into contact with the cutting line. Plants can die if you damage the bark. Battery duration Battery duration is dependent on the wortking conditions: light conditions: up to 500 metres medium conditions: up to 300 metres tough conditions: up to 50 metres For Your Safety Warning! Switch off, remove battery from machine before adjusting or cleaning. The blade continues to rotate for a few seconds after the trimmer is switched off. Caution – do not touch rotating blade. Assembly A Cutting and Edging B C D 14 • F016L70 457 • 06.12 English - 4 Before any work on the machine itself, remove battery from machine. Note: To ensure long and reliable service, carry out the following maintenance regularly. Regularly check for obvious defects such as loose fixings, and worn or damaged components. Check that covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before using. If the trimmer should happen to fail despite the care taken in manufacture and testing, repair should be carried out by an authorized customer service agent for Bosch garden products. For all correspondence and spare parts orders, always include the 10-digit part number (TYP) from the nameplate of the machine! Before any work on the machine itself, remove battery from machine. To remove the worn blade 16 push in direction of the arrow until it snaps off the pivot 17. Clean the pivot 17 of any residual plastic/debris with a sharp knife. To refit the new blade 16 place the eyelet over the pivot 17 and pull outwards until it snaps into place. Note: Only use Bosch replacement blades. They have been developed specially for improved cutting performance. The use of other cutter blades will lead to a d...


Your review
Your name:
Please, enter two numbers from picture: