Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 7   File size: 351 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. • PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury, or even death. • Save these instructions PROFESSIONAL INSTALLATION IS HIGHLY RECOMMENDED Manufactured by National Steelcrafters of Oregon, Inc. D

downloaded: 7   File size: 735 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

This safety switch has two functions. 1. To recognize an overheat situation in the stove and shut down the fuel feed or auger system. 2. In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut down the auger, preventing the stove from overheating. NOTE: On some units, once tripped, like a circuit breaker, the reset button will have to be pushed before restarting your stove. On other units the thermodisk has no reset button and will reset itself once

downloaded: 6   File size: 735 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

FREESTANDING INSTALLATION A. HORIZONTALLY THROUGH WALL (refer to Figure 8) NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions. 1. Position stove, adhering to clearances shown in Figures 1 & 2. 2. Locate position of hole in wall; directly behind stove exhaust vent (refer to figure 5). 3. Always maintain 3” clearance from combustible materials. 4. Install L-Vent wall thimble per L-Vent manufacturer’s instructions. 5. Attach enough piping to penetrate and extend at least 6” b

downloaded: 4   File size: 925 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. • PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury, or even death. • Save these instructions. PROFESSIONAL INSTALLATION IS HIGHLY RECOMMENDED Manufactured by Breckwell Hearth Products Eugene, Orego

downloaded: 0   File size: 925 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

AT LEAST THREE FEET FROM THE OPERATING STOVE. e. Maintain proper ventilation. It is important that adequate oxygen be supplied to the fire for the combustion process. Modern houses are often so well insulated that it may become necessary to open a window slightly or install an outside air vent to provide sufficient combustion air. f. Since heating with a solid fuel is potentially hazardous, even with a well made and thoroughly tested stove, it would be wise to install strategically placed smoke

downloaded: 0   File size: 925 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

Your blowers will never shut off and if the fire went out the auger will continue to feed pellets until the hopper is empty if you leave the POF thermodisk bypassed. 9. The high limit thermodisk has tripped or is defective. Using the owner’s manual, locate the high limit thermodisk. There is a red button located on the back of it. Press the red button. If you hear a click, the high limit had tripped. The stove should now function normally. To test if the thermodisk is bad, you can bypass it as d

downloaded: 1   File size: 945 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. . CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA. . PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS MULTI-FUEL BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. . SAVE THESE INSTRUCTIONS. .BRECKWELL HEARTH PRODUCTS 11/09 OWNER’S MANUAL TABLE OF CONTENTS INTRODUCTION .......................

downloaded: 6   File size: 584 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

When passing through additional floors or ceilings, always install firestop spacer. 2. After lining up for hole in roof, cut either around or square hole in roof, always 3” larger all the way around pipe. Install upper edge and sides of flashing under roofing materials, nail to the roof along upper edge. Do not nail lower edge. Seal nail heads with non-hardening waterproof mastic. 3. Apply non-hardening, waterproof mastic where the storm collar will meet the vent and flashing. Slide storm collar

downloaded: 2   File size: 371 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

9. The high limit thermodisk has tripped or is defective. Using the owner’s manual, locate the high limit thermodisk. There is a red button located on the back of it. Press the red button. If you hear a click, the high limit had tripped. The stove should now function normally. To test if the thermodisk is bad, you can bypass it as described previously for the POF thermodisk. 10. The F2 fuse on the control board has blown. Remove the control board. On the back there are two fuses. The one closer

downloaded: 14   File size: 745 kb   Manafacture: Breckwell  
Category: Kitchen-ranges
@name

The fireplace and chimney should be cleaned thoroughly before starting the installation. We suggest painting the interior of particularly old and dirty fireplaces to seal any odors. In zero-clearance fireplace installations, when the fireplace opening is above the floor or raised hearth, the adjustable “Breckwell P24 Z-C Skirt” (part # A-ZC-SKRT), or “Breckwell P24 Z-C Legs” (part #A-S-ZCLEGS), can be used to bridge the gap between the hearth and stove bottom. (Refer to figure 13) A. ASSEMBLING





Category