Votes - 1, Average rating: 2 ( )

User manual Bosch, model SGS57M92EU/36

Manafacture: Bosch
File size: 2.37 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page

Other manuals for this model:

manual abstract

The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Hold down programme button # and press main switch ( until the digital display illuminates. – Release both buttons. The LED for button # flashes and the digital display 8 displays the setting †:‹‹ (off) or †:‹‚ (on). To change the setting: – By pressing the button #, you can switch intensive drying on †:‹‚ or off †:‹‹. – Switch off the main switch (. The set value is saved. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators ` and h. If required, refill salt and/or rinse aid. en Filters The filters 1b keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 12 and 1B. – Check outlet nozzles on the spray arms for blockages. – Unscrew the upper spray arm 12. – Remove the lower spray arm 1B upwards. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. – Clean spray arms under running water. –Re-engage or screw on spray arms. en Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. Note If the appliance stops during dishwashing for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Basic functions”) a=Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: – First disconnect the appliance from the power supply. – Remove the bottom basket. – Remove the filters 1b. (See chapter entitled Maintenance and care) – Scoop out water, use a sponge if required. – Using a spoon, prise off pump cover (as illustrated) until it clicks, then grip the cover by the lug and pull it out forwards. – Check inner compartment and remove any foreign objects. – Place cover in the original position, press down and engage. – Install filters. Note If the cover is not engaged properly, this may cause a programme interruption. en ... when the appliance is switched on The appliance does not start. – The mains fuse has tripped. – The appliance plug has not been inserted. – The appliance door has not been shut properly. – Tap turned off. – Water supply interrupted. – Supply hose kinked. – Filter in the water supply blocked. – Switch off the appliance and pull out the mains plug. – Turn off the tap. – Clean filter in the supply hose. – Reconnect power supply. – Turn on the tap. – Switch on the appliance. – Water is left in the appliance at the end of the programme. – Waste water hose is blocked or kinked. – Waste water pump blocked, cover on the waste water pump is not locked in position. (see Waste water pump). – Filters blocked. – The programme has not yet ended. Wait until programme ends or implement “Reset” function. ... on the appliance Lower spray arm rotates sluggishly. – Spray arm blocked. The door is difficult to open. * – Child-proof lock is activated. The deact...


Your review
Your name:
Please, enter two numbers from picture: