Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 1   File size: 111 kb   Manafacture: Master Appliance  
Category: Blowtorches
@name@name@name

Becomefamiliar with all controls for safety. Lisez ce manuel entierement avant de commencer a utiliser l'outil. Familiarisez-vous avec tous les controles de securite. UL® Gas filling nozzle Lea completamente este manual antes de tratar de Bec de remplissage usar esta herramienta. Para mayor seguridad, famil de gaz Boquilla de carga de gas iaricese con todos los controles. Overall length 8.24 in Diameter 0.95 in Longueur totale • Largo total 210 mm Diametre • Diametro 24 mm Weight (when gas fille

downloaded: 0   File size: 734 kb   Manafacture: Master Appliance  
Category: Blowtorches
@name@name@name

Only empty fuel tank in a well ventilated area and away from ignition sources. Remember butane is heavier than air. 2. Depress the filler valve at the back of the tank with a small bladed screwdriver and let the butane gas escape through the small orifice opening. It takes approximately one minute for the butane to escape from the tank. Be careful that the butane does not hit against your fingers or hands. This could cause frostbite of the skin. 3.One method is to poke a small bladed screwdriver

downloaded: 5   File size: 734 kb   Manafacture: Master Appliance  
Category: Blowtorches
@name@name@name

Merci de lire ce manuel, s’assurer de l’avoir compris et le conserver en reference. Por favor lea, entienda y guarde este manual para referencia futura. Regulatory Information Declaration of Conformity: (According to EN 45014) Manufacturer’s Name: Master Appliance Corp. Manufacturer’s Address: 2420 - 18th Street Racine, WI 53403 U.S.A. Declares that the following product: Product Name: UT-100, UT-200 Conforms to the following product specifications: SAFETY DIRECTIVES: EN 123 12.81, EN 292 Parts

downloaded: 6   File size: 267 kb   Manafacture: Harbor Freight Tools  
Category: Blowtorches
@name

Serious personal injury and risk of fire may result. Setting up the Soldering Iron: The Torch comes with the “Soldering Iron Adapter” already installed. It is the longer of the two adapters and has a threaded end that receives the soldering tips. If you do need to install “Soldering Iron Adapter”, first remove the “Adapter Lock Nut” then slide the “Soldering Iron Adapter” over the ceramic insulator, then thread on the “Adapter Lock Nut”. Pick the desired tip from the kit and screw it onto the en

downloaded: 0   File size: 1 mb   Manafacture: Napoleon Fireplaces  
Category: Blowtorches
@name

CAN-2.21-M85 . IAS US. 4-96 GSST8N NATURAL GAS GSST8P PROPANE - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS: . Do not try to light any appliance. . Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions. . If you cannot reach your gas supplier, call the fire department. - Inst

downloaded: 1   File size: 1 mb   Manafacture: Napoleon Fireplaces  
Category: Blowtorches
@name

(refer to your manual for clearances) Mark all 14 hole centres on the wall (surface) using the template. 2. Remove the template. Depending on the surface and fasteners, drill the appropriate holes. Hold the Torch up, aligning the mounting brackets to the mounting holes. Secure the Torch to the wall using the appropriate fasteners. NOTE: The Torch has been designed to have a 1/2” clearance between the rear outer panel and the mounting surface. 3. Start the fasteners into each of the six remaining

downloaded: 0   File size: 989 kb   Manafacture: OK International  
Category: Blowtorches
@name

Both of these consumables are available from your authorized OK International distributor as needed. The power supply features a Power Switch, green “Power On” indicator light, power cord, and a connecting port for the solder handle cord. 1. Mount the power supply in a convenient location in your workspace, such as on the workbench. 2. Insert a heater tip onto the Coil Assembly and simply push the Heater Tip all the way until it seats. You should feel a slight “ click” as it locks into place. In

downloaded: 2   File size: 180 kb   Manafacture: Global Machinery Company  
Category: Blowtorches
@name

• Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devises Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Operation WARNING. Before connecting a tool to a power source, be sure th

downloaded: 1   File size: 250 kb   Manafacture: RIDGID  
Category: Blowtorches
@name

Catalog Sheet No. RT-175-96 Effective Date January 1, 1996 Model RT-175 Electric Soldering Gun The safer, flameless alternative to torches - The new RT-175 Electric Soldering Gun is a lightweight, rugged electric soldering gun that sweats joints on copper tube up to 3". The RT-175 will operate on a standard 115V, 15 AMP outlet. There is no open flame to worry about igniting wallboard, insulation, or studs and joists in the walls. Simply place the carbon tips on the copper fitting and remove

downloaded: 0   File size: 596 kb   Manafacture: RIDGID  
Category: Blowtorches
@name@name@name

. 19 WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and fol- low the contents of this manu- al may result in electrical shock,fire and/or serious per- sonal injury. OPERATOR’S MANUAL RT-175 • Francais – 9 • Castellano – pag. 19 WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and fol- low the contents of this manu- al may result in electrical shock,fire and/or serious per- sonal injury. OPERATOR’S MANUAL RT





Category