Votes - 3, Average rating: 3.7 ( )

User manual American Standard, model T010.740

Manafacture: American Standard
File size: 660.94 kb
File name: 3ee76b36-a9f5-404b-9585-c498f80f4212.pdf
Language of manual:enesfr
Free link for this manual available at the bottom of the page

manual abstract

Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT 186mm (7-3/8) 100mm (3-7/8) 200mm (7-7/8) 48mm to 68mm (2 to 2-5/8) 150mm (6) NOTE: FITTING MUST BE INSTALLED WITH VOLUME CONTROL ON TOP. R520 1/2" NPT INLETS or R540 3/4" NPT INLETS 25mm (1) FINISHED WALL TOP M968022 1 Remove PLASTER GUARD (1) if attached. Push CAPS (2 & 2a) as shown onto CONTROL VALVES (3). Push ESCUTCHEON HOLDER (4) with lightly greased O-RING SEALS (5) over CAPS (2, 2a). Attach the FIXATION PLATE (7) to the ESCUTCHEON HOLDER (4) with the two SCREWS (6) provided. Push ESCUTCHEON (8) flush against finished wall. 1 TRIM INSTALLATION 12 INSTALL HANDLES Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: TRANSPOSED SUPPLY PIPING 3 OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim. (Reverse steps 1 and 2). CHECK STOP (RED TO BLUE) Turn the water supply back on and perform the temperature adjustment in step 4. Assemble HANDLES and TRIM. CHECK STOP (BLUE TO RED) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. 2 2 2a 1 4 5 6 8 1 4 3 3 7 8 Attach HANDLE ADAPTER (1) to KNOB MOUNT (2) with SCREW (3). Align HANDLE (4) as shown and push onto KNOB MOUNT (2). Tighten SET SCREW (5) with HEX WRENCH (6) supplied with trim kit. Install HANDLE SCREW (7) into VALVE STEM (8) and tighten. Align HANDLE (9) as shown and push onto HANDLE SCREW (7). Tighten SET SCREW (5a) with HEX WRENCH (6) su pplied with trim kit. 6 9 5 5a 7 M968022 4 4 4 TEMPERATURE ADJUSTMENT SET HOT LIMIT STOP Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 12 o'clock position. See Figure 1. For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (4) until the spout temperature is 100°F. Check that arrow "A" on the KNOB MOUNT (4) still points 12 o'clock position after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (4) by pulling it towards you while standing directly in front of the valve. Reinstall the KNOB MOUNT (4) with arrow "A" 12 o'clock position. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE. See Step 2 for HANDLE (3) installation. ARROW "A" BLACK CLAMP ARROW "B" RED LOCKING DEVICE TEMPERATURE LIMIT STOP ARROWS AT 12 O'CLOCK Figure 1 POSITION KNOB MOUNT 112 109 104 3 1 2 Loosen SET SCREW (1) with HEX WRENCH (2). Pull off HANDLE (3). M968022 MODEL NUMBER A907090-YYY0A CAP M962630-0070A ESCUTCHEON HOLDER M907712-YYY0A ESCUTCHEON M918318-0070A HANDLE SCREW M962731-YYY0A HANDLE KIT CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT T010.740 GREEN TEA For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © AS America, Inc. 2008 HOT LINE FOR HELP M918038-0070A ADAPTER M918990-0070A SELF TAPPING SCREW CHROME SATIN NICKEL STAINLESS STEEL 002 295 075 Replace the "YYY" with appropriate finish code 023774-0070A SCREWS A924335-0070A FIXATION PLATE GREEN TEA T010.740 Installation Directives M968022 Nous vous remercions d'avoir choisi American Standard… synonyme de qualite superieure depuis plus de 100 ans. Pour que l’installation se deroule sans probleme, veuillez lire attentivement ces instructions avant de commencer. Certifie conforme aux normes ANSI A112.18.1M ASSE 10...


Your review
Your name:
Please, enter two numbers from picture: