Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 0   File size: 232 kb   Manafacture: Hitachi  
Category: Power Screwdrivers and Drills
@name@name@name

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. (7) Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. (8) Use only accessories that are recommended by the manufacturer for your model. Accessories

downloaded: 0   File size: 232 kb   Manafacture: Hitachi  
Category: Power Screwdrivers and Drills
@name@name@name

5 English 8. Mounting the bit For details, refer to the item “Mounting and dismounting the hex-socket or the bit”. Self-drilling screw Fig. 6 1 – 1.5 mm Sub-Stopper (A) HOW TO USE THE SCREW DRIVER 1. Switch operation and rotational speed adjustment Bit rotational speed can be regulated between 0 – 2600/min (W6VB2) or 0 – 1700/ min (W8VB) varying the degree by which the trigger switch is pulled. Rotational speed increases as the trigger switch is pulled, and reaches a maximum speed of 2600/min (W

downloaded: 1   File size: 1 mb   Manafacture: InFocus  
Category: Power Screwdrivers and Drills
@name

This will ensure that the safety of the power tool is maintained. PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons. English SPECIFICATIONS Model W6VM W6V4 W6VA4 W6VB3 W8VB2 Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V) Power input 620 W No-load speed 0 – 6000/min 0 – 4500/min 0 – 3000/min 0 – 2600/min 0 – 1700/min Capacities 6 mm 8 mm Bit shank size 6.35 mm Hex. Weight (without cord) 1.4 kg 1.5

downloaded: 0   File size: 11 mb   Manafacture: King Canada  
Category: Power Screwdrivers and Drills
@name

#ts10556 printed in taiWan .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

downloaded: 0   File size: 2 mb   Manafacture: InFocus  
Category: Power Screwdrivers and Drills
@name@name@name@name@name@name@name

4. After installing the driver bit, pull lightly out the bit to make sure that it does not come loose. If the bit is not installed properly, it can come loose during use, which can be dangerous. 5. Use the bit that matches the screw. 6. Tightening a screw with the impact driver at an angle to that screw can damage the head of the screw and the proper force will not be transmitted to the screw. Tighten with this impact driver lined up straight with the screw. 7. Always charge the battery at a tem

downloaded: 0   File size: 436 kb   Manafacture: Black & Decker  
Category: Power Screwdrivers and Drills
@name@name@name

Note: The charger will not charge a battery pack if the pack temperature is below approximately 32°F (0°C) or above 122°F (50°C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down. 2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or ba

downloaded: 1   File size: 282 kb   Manafacture: Black & Decker  
Category: Power Screwdrivers and Drills
@name@name@name

• Use only under adult supervision, keep out of the reach of children. • Ensure outlet is secured and completely intact. Do not plug charger into a loose wall outlet. IMPORTANT CHARGING NOTES • While charging, the charger transformer may hum and batteries and charger become warm. This is a normal condition and does not indicate a problem. • If a battery does not charge properly— (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected

downloaded: 0   File size: 345 kb   Manafacture: Alpine  
Category: Power Screwdrivers and Drills
@name

WHEREVER YOU ARE, REMEMBER, WE ARE AS CLOSE AS YOUR PHONE, FAX OR COMPUTER. CALL: 914-592-1220 FAX: 914-347-2181 Email: ue@worldnet.att.net Internet: NEED HELP??? HAVE QUESTIONS?? AT UE SYSTEMS, WE ARE DEDICATED TO SUPPORTING OUR ULTRAPROBE USERS. OUR STAFF HAS YEARS OF FIELD EXPERIENCE AND IS STANDING READY TO ASSIST YOU SHOULD YOU NEED US. WHEREVER YOU ARE, REMEMBER, WE ARE AS CLOSE AS YOUR PHONE, FAX OR COMPUTER. CALL: 914-592-1220 FAX: 914-347-2181 Email: ue@worldnet.att.net Internet: (FreeT

downloaded: 3   File size: 1 mb   Manafacture: MURO  
Category: Power Screwdrivers and Drills
@name

Before use, be sure to carefully read the instructions. Read the related Drill instruction manual, too. . Be sure to wear protective goggles during work. . Be sure to wear a dust-proof mask during work. . Depending on the work environment, wear ear protectors, hardhat, working shoes, and other safety gear. . Be sure to use the specified Adaptor Kit that is dedicated to your Drill model. . Be sure to use the specified "VISROPE" connecting screws. . Ensure solid footing and hold yourself in a safe

downloaded: 0   File size: 696 kb   Manafacture: Hitachi  
Category: Power Screwdrivers and Drills
@name@name@name

32 SPECIFICATIONS ................................................ 33 Page ASSEMBLAGE ET FONCTIONNEMENT .......................... 34 UTILISATIONS ..................................................... 34 METHODE DE RETRAIT ET D’INSTALLATION DE LA BATTERIE .......................................... 34 METHODE DE RECHARGE ................................. 34 AVANT L’UTILISATION ...................................... 37 UTILISATION ....................................................... 37 PLAGE D’





Category